查找模块的方法可参照:Simulink 查找元器件的四种方法
电力仿真模块一般在 Simscape/Electrical/Specialized Power Systems 目录下,外观是黑色。(俗称黑库)
当然,Simscape/Electrical (大部分元件是蓝色,俗称蓝库) 下面也有不少其他电力仿真的元器件,但是要注意不同库的模块不能相连。
比如: 来自 Simscape /Foundation Library /Electrical / Electrical Elements 的 Electrical Reference:

来自 Simscape / Electrical / Specialized Power Systems / Utilities 的 Ground: 
两个虽然功能相似,但不能混用!
本文将介绍以下模块(Specialized Power Systems 目录下):
名字模块直流电压源DC Voltage Source三相电源Three-Phase Source三相电压电流测量模块Three-Phase V-I Measurement(单相)电阻、电感和电容Series RLC Branch三相电阻、电感和电容Three-Phase Series RLC Branch派克(反)变换abc to dq0, dq0 to abc电桥Universal Bridge三相断路器Three-Phase Breaker锁相环PLL(3ph) 1. 直流电压源 DC Voltage SourceSimscape / Electrical / Specialized Power Systems / Fundamental Blocks / Electrical Sources
1000V直流电压源: 
Simscape / Electrical / Specialized Power Systems / Fundamental Blocks / Electrical Sources 
三相电源模块实现一个具有内部R-L阻抗的平衡三相电压源。 三个电压源在Y中连接,可以内部接地或可接近的中性连接。 可以通过输入R和L值直接指定源内阻和电感,也可以通过指定源感应短路电平和X/R比间接指定源内阻和电感。 例如:

Simscape / Electrical / Specialized Power Systems / Fundamental Blocks / Measurements 
三相V-I测量块用于测量电路中的瞬时三相电压和电流。 当与三相元件串联时,它返回三个相对地或相对相的峰值电压和电流。 该块可以输出电压和电流单位(pu)值或伏特和安培。
下图为测量电压电流的示例: 
具体使用方法可参照:【Simulink】Three-Phase V-I Measurement 使用方法
4.(单相)电阻、电感和电容 Series RLC BranchSimscape / Electrical / Specialized Power Systems / Fundamental Blocks / Elements
串联RLC分支:单个电阻,电感或电容,或这些的系列组合。电阻、电感和电容允许为负值。 其余模块类似: 
Simscape / Electrical / Specialized Power Systems / Fundamental Blocks / Elements 
15mH 电感和 0.01Ω 电阻的串联组合: 
三相串联RLC支路块由一个电阻、一个电感或一个电容或这些的串联组合组成。
其余类似: 
Three-Phase Series RLC Load: 
Three-Phase Parallel RLC Load:(恒功率1MW负载) 
Simscape / Electrical / Specialized Power Systems / Control & Measurements / Transformations

旧版本中还有一个输入 sin_cos,新版本去掉了。
两个参数分别对应不同的派克矩阵: 

一般采用 90 degrees behind phase A axis 。
7. 电桥 Universal BridgeSimscape / Electrical / Specialized Power Systems / Fundamental Blocks / Power Electronics
Diodes 二极管
Thyristors 晶闸管
GTO 门极可关断晶闸管 
MOSFET 电力场效应晶体管 
IGBT 绝缘栅双极晶体管 
Simscape / Electrical / Specialized Power Systems / Fundamental Blocks / Elements
Initial status :初始状态 (如上图即为关闭) Switching times :切换状态的时间 (如下图设置,即为在0.5s时断开) 
Simscape / Electrical / Specialized Power Systems / Control & Measurements / PLL 
顾名思义,输入三相电压/电流,可得到相位信息(wt) 参数一般默认即可 用数学模型搭建 PLL 可参考: 【Simulink】锁相环模块